PB TEEN Hampton Storage Bed Quick Start Manual
For your safety and ease, assembly by two adults is recommended.
Read all instructions before beginning assembly.
Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The
shipping box provides and ideal work surface. Do not dispose of any contents until assembly is completed
to avoid accidentally discarding small parts or hardware.
A – Headboard – 1 pc
D – Center Panel – 4 pcs
F – Long Hex Bolt – 12 pcs
I – Big Flat Washer – 12 pcs
L – Phillip Head Screw – 24 pcs
O –Leveler – 4 pcs
TOOLS REQUIRED (but not included):
Phillip Head Screwdriver
B – Footboard – 1 pc
E – Support Leg – 1 pc
G – Short Hex Bolt – 8 pcs
J – Small Spring Washer – 8 pcs
M –Wooden Dowel – 8 pcs
P – Wooden Block – 4 pcs
www.pbteen.com
C – Siderail Box – 2 pcs
H – Big Spring Washer – 12 pcs
K – Small Flat Washer – 8 pcs
N –Allen Key – 1 pc
Table of Contents
Related Manuals for PB TEEN Hampton Storage Bed
Convertible loft media (7 pages)
Hampton convertible loft bookcase (7 pages)
Headboard/footboard (3 pages)
Summary of Contents for PB TEEN Hampton Storage Bed
- Page 1 Hampton Storage Bed PRE-ASSEMBLY: • For your safety and ease, assembly by two adults is recommended. • Read all instructions before beginning assembly. • Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The shipping box provides and ideal work surface.
- Page 2 ASSEMBLY INSTRUCTIONS: 1. Lay the Siderail Box (C) upside down on a soft, scratch-free surface. 2. Attach the Leveler (O) to the bottom of the Siderail Box (C) using a Small Spring Washer (J), Small Flat Washer (K) and a Short Hex Bolt (G), insert through the pre-drilled holes on the Leveler (O) and into the pre-drilled hole on the bottom of the Siderail Box (C) as shown below;.
- Page 3 8. Lay the Center Panels (D) over the inner groves on both Siderail Boxes (C) as shown below. Insert Phillips Head Screws (L) in the pre-drilled holes; tighten using a Phillips Head Screwdriver. Figure 3 CARE INSTRUCTIONS: • Avoid direct sunlight and excessive temperatures. •.
- Page 4 Hampton Shelf Tower PRE-ASSEMBLY: • Please read all instructions before assembling. • For your safety, assembly by two adults is recommended. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. Avoide the use of a power drill as it may cause cracking. PARTS INCLUDED: A –Tower –.
- Page 5 10. Place Phillips Head Screws (F) through the pre-attached hinge into the pre-drilled holes located on the Tower (A); tighten using a Phillips Head Screwdriver as shown. Repeat for other door. 11. Determine the desired level for the Shelves (D). Insert the Shelf Pegs (E) into the pre-drilled holes on the interior sides of the Tower (A).
- Page 6 Hampton Hutch PRE-ASSEMBLY: • Please read all instructions before assembling. • For your safety, assembly by two adults is recommended. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. PARTS INCLUDED: A – Hutch – 1 pc PARTS REQUIRED (but not included): B –.
- Page 7 ASSEMBLY: 13. Attach the Drill Bit (G) to the Power Drill. Locate the partially-drilled holes on the inside of Hutch (A). Hold and press Wood Block (H) on the opposite side of the hole to prevent any breakage or damage when drilling as shown below in Figure 1.
- Page 8 15. Turn Left & Right Shelf Tower (B) upright; ensure the Towers (B) are completely level before attaching the Hutch (A), so that they align at a 90 degree angle to the Hutch (A) once assembly had been completed. 16. Using two people place the Hutch (A) in between the two Towers (B). Place the Connection Sleeve (C) into the pre-drilled holes on the interior ends of the Hutch (A) and the Connecting Screw (D) into the pre- drilled holes on the interior sides of the Left &.
Hampton shelf tower Hampton hutch
